Fabric Inspection Scores before Cutting

Turning roll reports into production decisions

By Lucen Ma, NOVITA

A fabric roll can meet its visual grading limit while its release for cutting remains unresolved. The shade approval may be missing, a test report may refer to a different batch, or the available width may not fit the planned marker. A buyer who sees only a passing score cannot tell which of these questions has been answered.

The practical task is to connect the inspection findings to a specific production decision: which material may be cut, for which order, under whose approval. This guide proposes a way to make that decision traceable, from checking the reported score to handing released rolls to the cutting room.

Establish what the score actually measures

Start with the inspection method and reporting basis. ASTM D5430-26 covers visual examination and grading of fabrics. Its public scope allows the methods to support acceptance of individual rolls and shipments when purchaser and seller agree. ASTM also notes that different point-assignment options can produce different totals for the same rolls. [1]

An inspection report should therefore identify the method, edition and scoring option. A heading that says only “four-point inspection” leaves too much open. Ask which rolls and lengths were inspected, which side was examined, and which conditions governed the examination. If the mill and an independent inspector disagree, establish whether they used comparable procedures before debating the result.

The reporting unit matters just as much. Points per 100 linear yards and points per 100 square yards measure different things. For an agreed area basis, the calculation is:

Points per 100 square yards = (total penalty points x 3,600) / (inspected length in yards x fabric width in inches).

The factor 3,600 converts inches to yards and expresses the result per 100 square yards. Use the width basis specified in the inspection procedure. J.Crew’s published 2022 fabric-inspection SOP, for example, uses ticketed width in this calculation; cuttable width is checked separately. [2] Replacing one width with another without explanation changes the score.

Request the inputs if a reported result cannot be reproduced. Keep the original unit alongside any conversion, and compare the score with an acceptance limit expressed on the same basis.

Keep roll acceptance separate from shipment acceptance

A shipment average can conceal a roll that exceeds its own limit. Where the purchase specification sets both individual-roll and shipment criteria, assess both. J.Crew’s 2022 SOP illustrates this distinction by setting separate roll and shipment limits for different fabric categories. Those are that buyer’s requirements, not universal limits for apparel production. [2]

When an area-based shipment score is required, divide the total penalty points by the total inspected area and express the result on the agreed basis. An unweighted average of roll scores can misstate the shipment result when their inspected areas differ. A short roll and a long roll should not receive equal weight merely because each occupies one line in a spreadsheet.

Also preserve the inspection scope. If the inspection covered a sample of the shipment, label it accordingly. A report for selected rolls does not establish that every roll was examined. The agreed sampling and acceptance plan should explain what can be concluded about the remaining material and when further inspection is needed.

Before approving production, the buyer should be able to identify any roll that needs a separate decision, even when the overall shipment result appears acceptable.

Check how the defects affect the planned garment

Keep a defect map or location record alongside the numerical grade. Two rolls with the same score may present different cutting problems. One might contain isolated flaws near an edge; another might have faults repeated through the area needed for front panels. The total alone does not describe that distribution.

Consider a localized stain. Avoiding it may be feasible if the marker leaves the affected area outside all required components. The cutting team still needs to check whether the revised layout produces the required size quantities from the available material. A workaround that uses more fabric can create a shortage even if the remaining panels are acceptable.

Repeated shading needs a different review. Confirm the approved shade reference and inspect how the variation would appear across components of the same garment. Grouping rolls by shade may help manage differences between rolls, but it does not by itself resolve variation within a roll. Any proposed use must satisfy the order’s appearance requirements.

Preserve the original inspection result when a cutting workaround is accepted. Record the defect location and any cutting restrictions. If the proposed use departs from the agreed requirements, obtain a documented concession identifying the material, permitted use and person authorizing the exception.

Confirm the separate tests needed for release

Visual grading cannot establish how fabric will behave in every later process or use. The purchase specification should identify the additional properties that need evidence and the test conditions that apply.

For example, AATCC TM135 measures changes in fabric length and width after specified home-laundering procedures. [3] A visual score cannot supply that result. If dimensional change is a release requirement, check the relevant report and its washing and drying conditions before approving the material for production.

AATCC TM8 addresses color transfer caused by rubbing, with dry and wet procedures. [4] Its result answers a crocking question. It does not establish performance under every other colorfastness test, so avoid describing a single result as proof that “colorfastness passed” without naming the test.

For each required report, match the fabric identity, color and relevant batch to the material being released. Check the sample identification, test date, method and agreed acceptance criteria. A report for development fabric may provide useful background while still leaving the bulk material’s status unresolved.

The release record should distinguish a failed result from a missing result. They require different follow-up: one calls for a disposition decision, while the other may require testing or retrieval of the correct evidence.

Work through a roll that passes its score limit

Suppose a buyer is sourcing navy cotton pique for polo shirts. An inspected roll is 96 yards long, its width on the agreed reporting basis is 58 inches, and it has 45 penalty points. These are hypothetical figures, used only to illustrate the calculation.

45 x 3,600 / (96 x 58) = 29.1 points per 100 square yards, rounded to one decimal place.

For this example only, the buyer has agreed an individual-roll limit of 30 points per 100 square yards. The result meets that visual-score requirement. Neither 30 nor any other figure in this example is presented as an ASTM limit or a NOVITA production policy.

Now suppose the required performance reports and cuttable-width check are complete, but the roll’s shade has not been approved against the agreed reference. The record should show:

  • Visual grading: meets the agreed score limit.
  • Required performance tests and cuttable width: accepted for this example.
  • Shade approval: outstanding.
  • Cutting release: on hold pending the named approver’s shade decision.

This wording tells the production team exactly what remains to be resolved. If shade is approved, update the release record with the reference and approval date. If the shade is rejected for the order, mark the roll rejected and record the agreed replacement or other disposition. Repeating the point calculation will not resolve a missing shade decision.

Give the cutting room an actionable release record

Use status terms that mean the same thing to purchasing, quality and production. The following is a proposed working convention; each business should align it with its own procedures and purchase agreements.

StatusMeaningInstruction to the cutting room
ReleasedRequired checks and authorizations are complete for the stated use.Cut only the identified material, following any recorded restrictions.
On holdEvidence, approval or a disposition decision is outstanding.Keep the material identified and out of cutting until the hold is cleared.
RejectedThe material is not accepted for the stated order or use.Segregate it and follow the agreed replacement, return or other disposition.

If material is released with an exception, write the restriction beside the release status. Avoid an unexplained “conditional pass” that leaves the operator to infer which panels, quantities or roll sections may be used.

A useful release record identifies:

  • Purchase order, garment style, fabric article and color.
  • Lot and roll numbers, including any sections excluded from use.
  • Governing specification and revision, inspection report, scope and scoring basis.
  • Required test reports, shade reference and approval status.
  • Final disposition, restrictions, decision owner and approval date.
  • Cutting order, lay and bundle references, so the material remains traceable after cutting.

Put the same release status on the roll identification and the production record used to issue fabric. When a new defect appears during spreading, pause the affected material, record its location and refer it back to the responsible person. Define the scope of that hold explicitly; a new observation on one roll should prompt an assessment of related material, not an undocumented decision about the whole shipment.

Agree the acceptance specification before ordering

The best time to settle these decisions is before bulk fabric is ordered. Agree the inspection method and edition, reporting unit, inspection coverage, roll and shipment limits, required performance checks and shade references. Identify who can authorize exceptions and what evidence is needed for reinspection or replacement.

For small apparel sourcing teams, a practical starting point is one shared release register with links to the supporting reports. Keep the inspection findings and the approval decision in separate fields. That makes it possible to update a decision without losing the original evidence.

For a detailed discussion of defect categories and acceptance specifications, see NOVITA’s fabric defect grading and acceptance guide.

Before issuing a cutting order, the production planner should be able to locate the approved roll list, any restrictions and the person responsible for the release. If one of those items is missing, resolve it before the roll reaches the table.

Technical references

[1] ASTM International. ASTM D5430-26, Standard Test Methods for Visually Inspecting and Grading Fabrics. Public scope and significance-and-use summary. Source

[2] J.Crew Group. Fabric and Merchandise Inspection Standards, revision dated May 4, 2022, printed pages 7 to 10. A buyer-specific example. Source

[3] AATCC. TM135, Test Method for Dimensional Changes of Fabrics after Home Laundering. Public method summary. Source

[4] AATCC. TM8, Test Method for Colorfastness to Crocking with a Crockmeter. Public method summary. Source

Discover more from Textile Details

Subscribe now to keep reading and get access to the full archive.

Continue reading